Harken 2142 57 mm Flip-Flop Block Manual do Utilizador descarregar pdf

Printed in USA 4623 04/14

Harken equipment requires minimal maintenance,

but some is required to give the best service and

to comply with Harken’s limited warranty.

Keep equipment clean by frequent flushing with fresh

water. Periodically clean with mild detergent and

water solution. Spin sheaves to distribute soap

solution evenly.

In corrosive atmospheres, stainless parts may show

discoloration around holes, rivets and screws. This is

not serious and may be removed with a fine abrasive.

IMPORTANT! Exposure to some teak cleaners and

other caustic solutions can result in discoloration of

part and is not covered under the Harken warranty.

For additional safety, maintenance and warranty

information see www.harken.com/manuals or

the Harken

catalog.

N15W24983 Bluemound Rd. • Pewaukee, WI 53072 U.S.A.

Telephone: (262) 691-3320 • Fax: (262) 701-5780

Web: www.harken.com • Email: [email protected]

Maintenance

Warranty

Flip-Flop Blocks

2142, 2143, 2144, 2145, 2678, 2679, 2688, 2689

Mount with 4 (SH) Sockethead Cap or (PH) Panhead Screws

2142, 2143, 2144, 2145 #10 (5 mm)

2678, 2679, 2688, 2689

/4" (6 mm)

Reeve

Line

INSTRUCTION SHEET

Strictly follow all instructions to avoid an

accident, damage to your vessel, personal

injury or death. See www.harken.com/

manuals for additional safety information.

Mount using ends to mark drill

holes. Make sure they are square

and against sheave assembly.

Use all four (4) fasteners with backing plates, washers

and locknuts. Deck or mounting surface must solid,

designed for block load. Consult with builder.

Drill

1 2 3 4

Resumo do Conteúdo

Página 1 - INSTRUCTION SHEET

Printed in USA 4623 04/14Harken equipment requires minimal maintenance, but some is required to give the best service and to comply with Harken’s

Página 2 - Reversing Cam Cleat

1. Loosen cam arm locking plate screw and pull outward to disengage.2. Rotate cam arm to desired position.3. Press locking plate in and tight

Página 3

1. Loosen cam arm locking plate screw and pull outward to disengage.2. Rotate cam arm to desired position.3. Press locking plate in and tight

Página 4

Printed in USA 4623 04/14Harken equipment requires minimal maintenance, but some is required to give the best service and to comply with Harken’s

Modelos relacionados 2143 57 mm Flip-Flop Block | 2144 57 mm Flip-Flop Block | 2145 57 mm Flip-Flop Block | 2678 75 mm Flip-Flop Block | 2679 75 mm Flip-Flop Block | 2680 75 mm Flip-Flop Block | 2681 75 mm Flip-Flop Block |

Comentários a estes Manuais

Sem comentários

Harken 2142 57 mm Flip-Flop Block Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Harken 2142 57 mm Flip-Flop Block. Harken 2142 57 mm Flip-Flop Block User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados 2143 57 mm Flip-Flop Block | 2144 57 mm Flip-Flop Block | 2145 57 mm Flip-Flop Block | 2678 75 mm Flip-Flop Block | 2679 75 mm Flip-Flop Block | 2680 75 mm Flip-Flop Block | 2681 75 mm Flip-Flop Block |

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Harken 2142 57 mm Flip-Flop Block