Harken 3811 System A CB & Slider Battcar Manual do Utilizador

Please read these instructions carefully before installing, servicing, or operating the equipment. This manual may be modified without notice: www.har

System A (CB/slider) 10CB System (Slug Mount) Install Track 4. Slide slugs into place with putty knife. Loosely install 5 mm x 20 mm screws.Tip: U

System A (CB/slider) 11CB System (Slug Mount) Install Track 7. Hold full-length track piece up to mast. Loosely install top screw.Use putty knife t

System A (CB/slider) 12Determining Track LengthBottom track must be short enough to remove easily. Use 457 mm to 609 mm (18" to 24") lengt

System A (CB/slider) 13IMPORTANT! To keep balls captive we recommend loading cars onto track without sail installed. Chart below shows correct numb

System A (CB/slider) 14CB System Load Cars on Track with Sail AttachedTip: Have another person help hold sail while you load cars.Cars with sail at

System A (CB/slider) 153883 Reef Car Load Sail on Cars1. Beginning with lower cars, use 4 mm hex key and 8 mm wrench or nut driver to attach sail

System A (CB/slider) 16CB/Slider Systems Load Sail on Cars4. Attach head of sail to headboard car with clevis pin and cotter pin.3. Load toggle usi

System A (CB/slider) 17Use shockcord to hold Lazy Jacks open so Battcars and battens will not catch on them when hoisting sail. This will also help

System A (CB/slider) 18Headboard coupler attaches to standard headboards - some headboard modification required.Maximum thickness of headboard plate

System A (CB/slider) 19CB/Slider—Battcars with Batten Receptacles—3830 CB/3803 Slider Sailmaker InstructionsOptional ShimUse enclosed rubber shim s

System A (CB/slider) 2Introduction WARNING! Strictly follow all instructions to avoid potential hazards that may kill or hurt you and others: ww

System A (CB/slider) 20AssemblyPlace batten receptacles on same side of sail. Make sure front of coverplate presses on swivel pin retainer that se

System A (CB/slider) 21Distance Between Attachment PointsBattens and intermediate cars placed at sailmaker's discretion. Maximum distance betw

System A (CB/slider) 22Sail setback from luff tape to intermediate car clevis pin will vary depending upon intermediate and batten car.Setback1777,

System A (CB/slider) 23CB/Slider Systems Installation TroubleshootingCB/Slider Systems Operation TroubleshootingClean beginning of season, or if c

Corporate HeadquartersN15W24983 Bluemound Rd, Pewaukee, WI 53072 USATelephone: (262) 691-3320 • Fax: (262) 701-5780Web: www.harken.com • Email: harke

System A (CB/slider) 3CB/Slider Systems PartsPart No. DescriptionLength Width WeightMax headboard thicknessMax battenBattenMaximum working loadWidt

System A (CB/slider) 4Track and AccessoriesPart No. Description IncludesMounting Slug Method3804, 3805 3806Track mounting kit(a) 15 mounting slugs 1

System A (CB/slider) 5CB/Slider Systems Sizing/Sail ModificationsSizingMake sure that you have the correct size Battcar system for your boat.Sail M

System A (CB/slider) 6Top track length chart: (use for 3807 slug mount track). Round track length to nearest 25 mm (1"). Note: Chart is based

System A (CB/slider) 72. Deburr cut.Slightly round track corners that will slide against mast.1. Cut special length top track from 2.05 m (6'8

System A (CB/slider) 8Clear of trysail track?CB/Slider Systems (Slug Mount) Check Fit of Mounting Slugs/CarCB cars 57 mm (21/4") Slider cars 3

System A (CB/slider) 91. Slip top track slugs into mast groove. Use 32 mm (1 1/4") mounting slug for top stop.2. One drop blue Loctite® adhesiv