Harken HYDRO 2 Power Unit  Manual do Utilizador

Please read these instructions carefully before installing, servicing, or operating the equipment. This manual may be modified without notice. See: ww

10 Hydro 2 Port IndentificationHydro 2: HPU has two (2) manifolds containing four (4) valve ports each. HPU remote manifold attaches via hose to pres

Hydro 2 11Hydraulic InstallationManifold Blanking PlatesAll manifold stations must have either blanking plates or valves. Once all functions have b

12 Hydro 2 Electrical InstallationHarken Hydro Units include 24 volt DC motors standard. 12 VDC motors are available by special order. If a 12VDC mot

Hydro 2 13Electrical InstallationConnect Deck Switches to the ECBInstall the deck switches in a convenient location. By design, two (2) deck switch

14 Hydro 2 Electrical InstallationConnect HPU to BatteryFollow these steps to connect HPU to Battery:1. A 250-300A circuit breaker or fuse (not suppl

Hydro 2 15CommissioningManufacturer Brand Name Manufacturer Brand NameAmocoRykon 46Gulf46AWAshland ValvolineEvergol 46MobilDTE 20 Series 25Atlantic

16 Hydro 2 CommissioningClosing CircuitVerify the system installation after completing hydraulic and electrical installation and filling the reservoir

Hydro 2 17OperationPower Up / Power DownHarken Hydro Power Units have system isolation switches on the electronic control box.During short-term, i

18 Hydro 2 MaintenanceCAUTION! If necessary, top off oil reservoir using proper fluid type. Do not mix oil types. Refer to Oil Equivalent Table, pg.

Hydro 2 19MaintenanceLeakage InspectionAfter commissioning visually inspect system for leaks. Perform visual leak inspection at regular intervals.

2 Hydro 2 INTRODUCTION ...

Bill of Materials H-5133718.504470.0024.016610.0124.368618.9620.020508.52118831114491376512101922025.500647.70NO.QTY.DRAWING NO.PART NO.MATERIALDESCR

PUMP SUCTION LINE(3/8" PIPE 9" LONG SCH 40)FILTERED RETURN LINE(1" PIPE 8" LONG SCH 40)NOT SHOWNPUMP TO MANIFOLD LINE HOSE,MANIFOL

22 Hydro 2 3D Rendering

Hydro 2 23CR1T G1OFFT AS13PL13PL14 4BLK WHTMOTOR 1 THERMAL SWITCHTHERMAL BY PASS SWITCHMOTOR 1 THERMAL RELAY+24A-2ON+24A-1LT 1CR1GND (-)MOTOR 1

24 Hydro 2 Suggested Wiring Practice for Motors Customer Supplied Batteries and DisconnectSURFACE FINISHMATERIALDRAWING NUMBERREV.FINISHPART #DATE

MOTOR #1CONTROL POWERON OFFMICO1 9000-41034-0100600SOL1A2 211BLUEBLKWHTVALVE1A COIL / B COIL+24-1PB1APB1BSOL1B2 ACB1SOL2ABLUEBLKWHTVALVE2A CO

Valve and Switch Wiring Schematic (#1 – #4) 234151-+24 VDC2-SOL A3-COMMON4-SOL B5-PE234151-NOT USED2-SOL A3-COMMON4-SOL B5-PEVALVE 2 A/B24 VDC22 WATTS

Valve and Switch Wiring Schematic (#5 – #9) 234151-+24 VDC2-SOL A3-COMMON4-SOL B5-PE234151-NOT USED2-SOL A3-COMMON4-SOL B5-PEVALVE 5 A/B24 VDC22 WATTS

Hydro 2 29Notes

Hydro 2 3Introduction Plumbing to manifolds is under reservoir top so there is no exposed plumbing (not visible).Harken Hydraulic Power Units (HPU

30 Hydro 2 Control Box Mounting Dimensions H-50335Note: Allow 1" (25 mm) clearance for toggle switch and indicator light132.365.211148.335.8403

Hydro 2 31Control Box Interior Layout GND(-)GND(-)GND(-)GND(-)GND(-) GND(-)GND(-)GND(-)+24A+24AGND(-)GND(-)GND(-)GND(-)GND(-)GND(-) GND(-)GND(-)GND

Corporate HeadquartersN15W24983 Bluemound Rd, Pewaukee, WI 53072 USATelephone: (262) 691-3320 • Fax: (262) 701-5780Web: www.harken.com • Online Catal

4 Hydro 2 Power Unit Selection / Parts *One function delivers double flow output (8 gpm) using 2 motors **This number is reduced by one when a double

Hydro 2 5SafetyImportant Safety InformationRead all instructions carefully and follow all safety precautions to avoid personal injury or property d

6 Hydro 2 SafetySafety RequirementsThe instructions provided with this manual are for installation and use only. The Harken Power Unit must only be s

Hydro 2 7Installation While unpacking the hydraulic power unit (HPU) and electronic control box (ECB), inspect for irregularities. During transport

8 Hydro 2 InstallationMount Control BoxChoose a suitable location for the electronic control Box (ECB) as described in the planning section. The ECB

Hydro 2 9Hydraulic Installation Hose and Fitting Selection RecommendationFunctions must be connected to the HPU manifold using proper hydraulic hos